CompactRIO Third Party Module Developers
PrintOverview
The National Instruments CompactRIO combines an open embedded architecture with small size, extreme ruggedness, and hot-swappable industrial I/O modules. Being powered by reconfigurable I/O (RIO) FPGA technology allows third party developers to create custom modules to meet industry specific needs and requirements.
Table of Contents
Featured Module
See the Combination Sensor Input Module from Drivven
Overview
Many third party companies offer custom deployment-ready C Series modules. Below you will find qualified CompactRIO Module Developers with ready-made hardware and driver software. If your application requires a custom I/O module with unique or specialized signal types, contact one of these suppliers and they will design a module to your exact needs.
- S.E.A. Wireless LAN with Switch Module
- S.E.A. Ethernet Switch Module
- S.E.A. ZigBee 10/20 Module (short range wireless networking)
- S.E.A. ZigBee 100/200 Module (wide range wireless networking)
- S.E.A. ZigBee 1000 Module (long distance wireless networking)
- S.E.A. GSM General Packet Radio Service Wireless Module (with EDGE support)
- S.E.A. GPSIB Module (includes IRIG-B, Synch, and Programmable Pulse)
- S.E.A. GPS Module (with additional Synch and Programmable Pulse)
- S.E.A. Gxxxplus Combo Module (includes GSM, EDGE, GPS, Synch, and Programmable Pulse)
- Geoprotek Tech, Wireless ZigBee Networking Module
Communication Bus and Protocol Modules
- Comsoft PROFIBUS DP Master/Slave Module
- S.E.A. LIN Module
- S.E.A. LIN A Module (with analog extension)
- S.E.A. EnDat Module (digital encoder interface)
- Averna MIL-STD-1553 Module
- AviaOK ARINC-429 Receiver Module
- AviaOK MIL-1553 Module
- AviaOK ARINC-429 Transmitter Module
- Data Ahead PROFIBUS DP Slave DP
- SET ARINC-429 transmitter Module
- SET ARINC-429 Receiver Module
- SET ARINC-429 Resolver Demodulator Module
- SET ARINC-429 Resolver Demodulator Simulator Module
- SET ARINC-429 LVDT Demodulator Module
- SET ARINC-429 LVDT Simulator Module
- PWG MIL-STD-1553 Module
- STeP UDP Multicast Broadcast Module
- STeP Ethernet POWERLINK
Vehicle Design and Prototyping Modules
- Drivven VR/Hall Module (includes VR and Hall effect sensor inputs)
- Drivven Port Fuel Injector Driver Module
- Drivven Combination Sensor Input Module
- Drivven Low-Side Driver Module
- Drivven Spark Driver Module
- Drivven O2 Sensor Module
- Drivven Diesel Injector Driver Module
- Drivven Electronic Controller HIL Module
- Drivven Electronic Throttle and IAC Valve Controller Module
- Drivven NOx Sensor Module Module
- Drivven Engine Synchronous TTL Output Module
- KGC Low-Side Switch module for cRIO
- KGC Solenoid driver module for cRIO
- KGC Voltage source module for cRIO
Motion Modules
Processor Modules
- Bluetechnix ADI Blackfin 537 Processor Modules
- Bluetechnix ADI Blackfin 537 with integrated JTAG Debug Processor Modules
Reader Comments | Submit a comment »
Legal
This tutorial (this "tutorial") was developed by National Instruments ("NI"). Although technical support of this tutorial may be made available by National Instruments, the content in this tutorial may not be completely tested and verified, and NI does not guarantee its quality in any way or that NI will continue to support this content with each new revision of related products and drivers. THIS TUTORIAL IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND AND SUBJECT TO CERTAIN RESTRICTIONS AS MORE SPECIFICALLY SET FORTH IN NI.COM'S TERMS OF USE (http://ni.com/legal/termsofuse/unitedstates/us/).