Company Events Academic Community Support Solutions Products & Services Contact NI MyNI

LabVIEW WSN Module Error Codes

LabVIEW Wireless Sensor Network Module Help

Edition Date: June 2013

Part Number: 372802E-01

»View Product Info

The LabVIEW WSN Module can return the following error codes. Refer to the KnowledgeBase for more information about correcting errors in the LabVIEW WSN Module.

Code Description
−25339 You must enable the serial port receiver power before calling this function, or no new data can be read.
−25338 The device does not support reading or writing the specified number of bytes from the serial port at one time.
−25337 The specified number of bytes cannot be read or written within the specified timeout.
−25336 The specified serial port configuration is unsupported on this device.
−25327 Not enough user RAM.
−25326 Invalid user RAM refnum. This error can occur when you try to perform an operation on a null refnum or a previously closed refnum.
−25325 Verification of user memory failed.
−25324 Failed to write to user memory.
−25323 Failed to write to user memory because the location is not empty. To correct this error, you must erase the entire user memory sector before you can write to the same location again.
−25322 User memory out of bounds. The operation specified a location outside the user memory sector.
−25321 Failed to erase the specified user memory sector.
−25320 Null pointer exception.
−25313 Internal error: Hardware failure.
−25312 The node is not connected.
−25311 Invalid argument.
−25310 User message missed.
−25309 Radio failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25308 Flash failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25307 Command queue overflow: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25306 Digital output line failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25305 ADC failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25304 CJC failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25303 SPI communication failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25302 Serial receiving failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25301 Serial transmission failure: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25300 An internal error has occurred in the LabVIEW Wireless Sensor Network Module. Please contact National Instruments technical support at ni.com/support.
−25283 The node ID does not exist in the gateway's node table.
−25282 Invalid message reference.
−25281 Invalid node reference.
−25280 Invalid gateway reference.
−25254 Connection timed out. Gateway might be in a bad state.
−25253 Double interface registration: An internal error has occurred. Please contact National Instruments technical support at ni.com/support.
−25252 Incompatible or corrupted data was received from the gateway.
−25251 Memory error. Unable to deallocate used memory.
−25250 Memory allocation failed.
−25230 The request processor failed to deserialize a request. This error can occur if protocol versions are incompatible or data is corrupt.
−25229 The request processor failed to deserialize a request. This error can occur if protocol versions are incompatible.
−25228 The request terminated due to an unhandled exception.
−25227 Memory allocation failed.
−25226 The client was denied access.
−25225 The client aborted the connection.
−25224 Network communication failed. This error can occur if the gateway IP address is incorrect, the gateway is disconnected, or the gateway is unable to complete the request before timing out.
−25223 Connection timed out.
−25222 Unable to connect to the named service.
−25221 Unable to connect to the named gateway.
−25220 Generic connection error.
21240 The serial port receiver received a break condition on the line.
21241 The specified number of bytes were read from the serial port before the specified termination string was detected.

 

Your Feedback! poor Poor  |  Excellent excellent   Yes No
 Document Quality? 
 Answered Your Question? 
Add Comments 1 2 3 4 5 submit