Company Events Academic Community Support Solutions Products & Services Contact NI MyNI

Error Codes (Electrical Power Suite)

LabVIEW 2013 Electrical Power Suite Help

Edition Date: June 2013

Part Number: 373375C-01

»View Product Info

The Electrical Power VIs can return the following error codes. Refer to the KnowledgeBase for more information about correcting errors in LabVIEW.

Code Description
−363499 time multiplier setting must be no less than 0.025 and no greater than 20.
−363498 GD must be no less than 2 and no greater than 64.
−363497 The values of reset time parameters must be greater than zero.
−363496 The values of curve data must be greater than or equal to zero.
−363495 The input energizing quantity G crosses the pick-up setting value Gs whereas pick-up signal? is still FALSE.
−363494 reset level must be less than or equal to Gs in the FPGA Threshold (Over) VI and must be greater than or equal to Gs in the FPGA Threshold (Under) VI.
−354699 You must set open mode to Create or Create or replace when you run this VI on real-time targets.
−354698 The numbers of analog channel info and status channel info must not be empty or exceed 999,999.
−354697 timestamp multiplier must be greater than or equal to zero.
−354696 The data channel number is not consistent with the actual configuration.
−354695 The required file is not open.
−354694 Manufacturer names must begin with a letter.
−354693 The ASCII code of characters of entry names must be between 33 and 127, in decimal.
−354692 An entry name must start with one word with 3-32 characters long.
−354691 You must set open mode to Create or Create or replace.
−354690 You must set open mode to Open (read only).
−354689 physical channels contains the same channel for multiple times.
−354688 physical channels does not contain the specified phasor channels.
−354687 The value of reporting rate is invalid.
−354686 The values of time base and number of PMUs must not be zero.
−354685 There must be 16 channels at most in each digital word.
−354684 phasors and magnitudes and phases must have the same array size.
−354683 The values of frequency high limit, frequency low limit, and df/dt limit must all be greater than zero.
−354682 The value of frequency high limit must be greater than the value of frequency low limit.
−354681 The values of magnitude low limit and magnitude high limit must be greater than zero.
−354680 The value of magnitude high limit must be greater than the value of magnitude low limit.
−354679 The value of phase-angle diff limit must be greater than zero and less than or equal to pi.
−354678 The size of magnitudes in and timestamps must be equal to the number of physical channels.
−354677 The channel numbers of magnitudes, phases, and timestamps must be the same.
−354676 The number of samples in data in must be equal to the value of samples to read from the previous iteration.
−354675 The number of samples in GPS information must be equal to the value of samples to read from the previous iteration.
−354674 The value of max time error must be greater than or equal to 0.
−354673 The value of channel index must be less than the number of channels minus one.
−354672 The value of nominal Fs/actual Fs must be greater than zero.
−354669 The aggregation interval you specify must be divisible by the next higher time unit of aggregation interval. For example, if you specify seconds as the time unit, then the next higher time unit is minutes. Thus the aggregation interval can be any number that is the divisor of 60, such as 10, 12, 15, 20, etc.
−354668 The aggregation interval must be greater than the time difference between two subsequent runs.
−354664 The length of channel units is out of range. The length of channel units must be in the range [1,32].
−354659 min rate of change is out of range.
−354658 max voltage change is out of range.
−354657 min steady state difference is out of range.
−354656 steadiness of steady state is out of range.
−354655 min steady state duration is out of range.
−354654 swell threshold is out of range.
−354653 dip threshold is out of range.
−354652 interruption threshold is out of range.
−354651 hysteresis is out of range.
−354649 The size of actual ranges must be the same as the size of spectra in.
−354648 The size of the first dimension of gains and phase delays must be equal to or greater than the size of spectra in.
−354647 The size of the second dimension of gains and phase delays must be the same as the size of frequencies to calibrate.
−354646 The size of the third dimension of gains and phase delays must be the same as the size of ranges to calibrate.
−354645 The configuration of physical channels does not match the wiring information in data in.
−354644 The values of frequencies to calibrate must be in ascending order.
−354643 The number of rows in phase delays must be equal to or greater than the size of one-cycle fundamental vectors in.
−354642 The number of columns in phase delays must be the same as the size of ranges to calibrate.
−354641 The size of actual ranges must be the same as the size of one-cycle fundamental vectors in.
−354640 The values of ranges to calibrate must be in ascending order.
−354639 The size of full-range RMS values must be equal to or greater than the size of waveforms in.
−354638 The size of offsets must be equal to or greater than the size of waveforms in.
−354637 The number of rows in gains must be equal to or greater than the size of waveforms in.
−354636 The number of columns in gains must be the same as the number of columns in ranges to calibrate.
−354635 The size of actual ranges must be the same as the size of waveforms in.
−354634 detection threshold is out of range.
−354633 start logical 1 length is out of range.
−354632 start logical 0 length is out of range.
−354631 maximum event length is out of range.
−354630 signaling frequency is out of range.
−354629 The value of data index does not correspond to the value of data in.
−354628 The value of spectra index or vector index does not correspond to complex spectra.
−354627 The number of columns in data in does not match the number of physical channels.
−354626 The value of channel index does not correspond to waveforms.
−354625 high limit must be greater than low limit.
−354624 hysteresis must be equal to or greater than zero.
−354623 Not a valid digital formula function.
−354622 The number of rows in data in does not match the number of samples per 10 or 12 cycles.
−354619 The size of sensitivity must be equal to or greater than the size of waveforms in.
−354618 The size of CT/VT ratio must be equal to or greater than the size of waveforms in.
−354617 The number of samples per cycle must be within the range of 128 to 512.
−354616 The number of samples per cycle must be even.
−354615 rate in the DAQmx Timing (Sample Clock) VI must be greater than the value of samples per cycle in the Initialize System VI times 57.5 for a 50 Hz electrical power system and times 69 for a 60 Hz electrical power system.
−354614 number of channels must be within 1 to 16.
−354613 reference channel index must be less than number of channels minus one.
−354612 The number of samples per cycle must be 192.
−354609 interval length is out of range. interval length must not be less than zero.
−354606 maximum harmonic order is out of range.
−354604 The size of the input array must be equal to three.
354609 The channel numbers of voltage and current data are not equal.
354618 In an unbalanced system, the re-calculated phase voltage values are approximate values.
354671 The value of analogs is out of range as a 16-bit integer. Set Bit 2 to 1 in data format of the Initialize System VI to change the format of analogs to floating point.
354672 The value of df/dt is out of range as a 16-bit integer. Set Bit 3 to 1 in data format of the Initialize System VI to change the format of df/dt to floating point.
354673 The frequency deviation from the nominal frequency is out of range as a 16-bit integer. Set Bit 3 to 1 in data format of the Initialize System VI to change the format of frequency to floating point.
354674 The value of phasors is out of range as a 16-bit integer. Set Bit 1 to 1 in data format of the Initialize System VI to change the format of phasors to floating point.
354675 The value of PMU ID is out of range. The value of PMU ID must be in the range [1, 65534].
354689 station name, phasor name, analog name, and digital names must be less than or equal to 16 characters. This VI automatically coerces long names to 16 characters.
354693 The total numbers of max sample text and min sample text per each public event information must not exceed 99.
354694 The length of channel phase identification must not exceed 2.
354695 The lengths of channel identifier, channel name, and monitored circuit component must not exceed 64.
354696 The number of sampling rates in the data file must not exceed 999.
354697 The number of entry names must be equal to the number of entry values.
354698 station name and recording device name must contain no more than 64 characters.
354699 The filename must be less than or equal to eight characters.
363498 Coercion occurs when this VI quantizes the curve in a discrete representation. The coercion may cause a slight operate timing inaccuracy or reset timing inaccuracy.
363499 Some values of operate or reset time are smaller than what the internal fixed-point data type can represent. This VI coerces these values to 0.002048.

 

Your Feedback! poor Poor  |  Excellent excellent   Yes No
 Document Quality? 
 Answered Your Question? 
Add Comments 1 2 3 4 5 submit